DOL 10 temperature sensor
From
€27.77*
Manufacturer item no.: 140246The DOL 10 is a simple temperature sensor. This sensor is well suited for use in environments that require a robust design and fast response time.The temperature sensor is used to measure the inside and outside temperature and has an accuracy of + 0.5 °C.The sensor has a temperature range of minus 40 to plus 60 °C and is protected according to IP67.The DOL 10 comes with a 1.5 meter cable. (Optional 5 meter cable, please inquire)TECHNICAL DATAelectricMeasuring range -40°C to +60°CAccuracy ±0.5°CEnvironmentAmbient temperature, operation and storage -40°C to +60°CProtection class IP 67sensor properties-40℃ 82.50kΩ 8.08V0°C 32.91kΩ 6.37V60°C 6.59kΩ 2.68V
DOL 104 humidity sensor 0-10V
From
€161.40*
Manufacturer item no.: 140263
The DOL 104 is a high precision relative humidity sensor. The sensor has an analogue output with very low output resistance and full protection against short circuits and cable faults. The special sensor element and the integrated filter enable use in livestock stables with a constantly high level of humidity. A protective cap is also available so that the sensor does not have to be removed when cleaning the barn.
Other models available on request:140279 DOL 104 humidity sensor 1-3V140273 DOL 104 humidity sensor 4-20mA140276 DOL 104 Humidity sensor 0.5-3V Rotem 8C
TECHNICAL SPECIFICATIONS
Measuring range 0 – 100% RH
Accuracy 2% RH (40-85%), 3% RH (10-95%) at 0-40°C *
Output signal 0.1V / % RH
Supply voltage 11 – 30 V DC
Supply current 12 mA no load 35 mA
max load Load > 500Ω - < 10MΩ
Recommended burden ≥ 100 kΩ
Output current 20 mA (current limited)
Output impedance < 1Ω
Temperature, operation and storage - 40 °C - 60 °C
IP classification IP 67
Cable 2 m. 3 x 22 AWG / 0.34 mm2
max. cable length/ 100 m 0.75 mm2 200 m 1.50 mm2
After direct exposure to water and condensation, a period of time with less than 80% relative humidity is required for a correct measurement.
Other variants available:
0-5V 0.05V / %RH
0-3V 0.03V / %RH
Similar to illustration
DOL 111 rain detector
From
€316.75*
Manufacturer item number: 140308
DOL 111 is an optical rain detector. It has built-in optical probes for rain detection and comes with a 30-meter cable for easy installation.
To ensure automatic closing of inlets in case of rain for example in cattle stables, DOL 111 rain sensor can be connected to a climate computer.
DOL 111 rain detector can give a signal when it rains over or below 6.35 mm/hour (1/4”/hour). The rain sensor can be adjusted to stop detection 30 sec. to 5 min. after last drop. The sensor can be used in temperatures between minus 40 and plus 60 degrees Celsius.
The rain detector is made of UV-resistant polycarbonate, UV-stable ABS, stainless steel, and has a silicone O-ring to protect the circuit board from rain.
The sensor can also be used for other detection purposes.
DOL 111 is designed to override cycle programs, stopping the system during rainfall, and keeping it off for a while after rain has fallen. Thus, it can be used with irrigation controllers for stopping sprinklers at the field e.g. Irrigation will resume once the sensor dries out or it rains below 6.35 mm/hour.
Technical data:
Supply voltage 10-15 VDC / 15 mA
Output signal relay NO 1A 24 VDC
Sensitivity medium: 6.35 mm/hour
Stops detection 30s to 5mins after the last drop
Cable 30m (4 x 22AWG / 0.34mm)
weight 1500 gr
Tip
DOL 112-PT100 temperature sensor
From
€19.44*
Manufacturer item no.: 140382
DOL 112-PT100 is a simple cost-effective temperature sensor. The sensor is a robust sensor with the high quality known from other dol-sensors’ sensor solutions. Thus, DOL 112-PT100 is well suited for use in environments where a sturdy design is required.
The temperature sensor can operate in temperatures between minus 40 and plus 100 oC and can be used for measuring both inside and outside temperatures.
DOL 112-PT100 is IP 68 protected, which means that it is dust tight and has total protection against water ingress, up to and including complete submersion below one meter and for more than 30 minutes.
The sensor has an accuracy of +0.5 oC and comes with a 2-wire 1.4-meter ø5 mm cable.
TECHNICAL DATAelectricMeasuring range -40°C to +100°CAccuracy ±0.5°CTolerance class B, F0.3Time constant T63 5 min. at 0.5 m/s air speedEnvironmentAmbient temperature, operation and storage -40°C to +100°CProtection class IP 68sensor properties-40℃ 84.27Ω0°C 100Ω60℃ 123.24Ωsensor dataTwo-core cable, length 1.40 mSensor Ø14, length 75mm
DOL 114 humidity and temperatur sensor
From
€188.06*
Manufacturer item no.: 140252
DOL 114 is a high-precision sensor for measuring relative humidity and temperature. The sensor was developed for use in livestock farming, but it is suitable for numerous industrial purposes. The sensor has two analogue outputs with very low output resistance and full protection against short circuits and cable faults. The special sensor element and the integrated filter enable use in livestock stables with a constantly high level of humidity. Depending on requirements, the sensor can be equipped with an integrated termination socket or a cable and with a specially adapted specification range. The sensor is controlled by a microprocessor and has a two-color LED diode for displaying operating status and fault diagnosis. The sensor is available with an extinguished diode on request.
Other variants available on request: 140260 DOL 114 humidity & temp. sensor 0-60°C 140253 DOL 114 Humidity & temp. sensor 5m cable 140254 DOL 114 humidity sensor including plug 0-10V 140282 DOL 114 RH & temp. sensor 0.5-3V red
TECHNICAL SPECIFICATIONS Measuring range:
Humidity: 0 – 100% RH 17 – 100% RH*
Temperature: - 40°C – 60°C 0 - 60°C
Accuracy :
Humidity: ± 2% RH (40-85%) ± 3% RH (10-95%) at 40°C
Temperature: +10°C - 40°C:± 0.5°C
- 30°C - 60°C: ±1.5°C Output signal:
Humidity: 0.1V/%RH
Temperature: 0.1V/°C; 0°C at 4V
Time constant T63: 20 s at 0.5 m/s air speed 6 min at 0.5 m/s air speed
Electrical connection: 11 – 30 V DC
Current: 12mA no load / 55mA max load
Load: > 500Ω - < 10MΩ
Recommended load: ≥ 100 kΩ
Output current: 20 mA per output (current limit)
Output Impedance: <1Ω
Operating and ambient temperature, storage: - 40 °C - 60 °C
IP classification: IP 67
Cable: 2m. 4 x 22AWG / 0.34mm2
Maximum cable length 100 m at 0.75 mm2 200 m at 1.50 mm2
Illustration similar
DOL 114 Plug system
From
€39.50*
Manufacturer item no.: 140292Plug connection for removing the sensors during cleaning work.A blind cap closes the plug connection during cleaning.Suitable for DOL 16/104/114
DOL 119 CO2 Sensor 5000/10000 ppm 0-10V
From
€398.60*
Manufacturer item no.: 140331
For measuring the CO2 content in the air. Supplied with M12 connector and sealing plug and protective cap for DOL 119. DOL 119 is a sensor for measuring the prevailing level of carbon dioxide/CO2. The sensor is used for climate monitoring via the CO2 content of the barn air. The measurement range of the sensor is based partly on monitoring the comfort zone of the animals and partly on monitoring possible error conditions in direct combustion houses. The sensor has two analogue outputs, with 0-10V power and 0-5V power respectively. Both are with low output impedance and full protection against short circuits and cable faults. The sensor is protected by a stable housing and its placement behind a carefully selected filter. The sensor is equipped with a cable and a protective cap so that it is not damaged during washing and disinfection work. The sensor must be installed in the middle of the barn building. TECHNICAL SPECIFICATIONS
Exit:
Measuring range (output 1) 0 - 10 VDC
Measuring range (output 2) 0 - 5 VDC
Limited output current per port 20 mA
Output impedance <1Ω
Recommended load impedance >100 kΩ
Max. cable length @ 0.75mm2 100 m
Max. cable length @ 1.50mm2 200 m
Load impedance 0.5 – 10000kΩ
CO2 – Output 1:
Measuring range 0-10000ppm
Output resolution 0.001V/ppm CO2
Accuracy 400 – 10000ppm 50ppm + 5% of reading ppm
Temperature stability (0-50°C) + 2.5 ppm/oC
Time constant: T63 2 minutes at 0.5 m/s air velocity
CO2 – Output 2:
Measuring range 0 - 5000 ppm
Output resolution 0.001V/ppm CO2
Accuracy 400 – 10000ppm 50ppm + 5% of reading ppm
Temperature stability + 2.5 ppm/oC
Time constant T63 2 minutes at 0.5 m/s air speed
General:
Power supply: 13.5 - 30 VDC
Supply Current: No Load 8mA, Max Load 55mA
Temperature, operation: CO2: CO2 valid 0 - +50 oC
Temperature, operation: -40 - +60 oC
Temperature, storage: -40 - +70 oC
IP protection class: IP67 (DIN 40050-9)
NEMA 1, 3, 4, 6
Cable Length: 2m
Cable conductor size: 4 x 0.34 (4 x AWG22) mm2
DOL 119/139 protective cap
From
€27.30*
Manufacturer item no.: 140261Protective cap for the DOL 119/139, which ensures that the sensor is not damaged during cleaning work, for example.1 set contains 5 pieces
DOL 12 temperature sensor
From
€19.46*
Manufacturer item no.: 140200 (Alternative for 140207, 140203, 140295)The DOL 12 temperature sensor is a simple temperature sensor. This sensor is well suited for use in environments where a robust design is required and can be used in temperatures between minus 40 and plus 100 °C.The sensor can be used to measure both indoor and outdoor temperature and is supplied with a 1.5 meter 2-wire cable.The DOL 12 sensor is IP 67 protected and has an accuracy of +0.5 °C.TECHNICAL DATAelectric Measuring range: -40 °C to +100 °C Accuracy: ±0.5°C Time constant T63 5 min at 0.5 m/s air speedEnvironment ambient temperature. Operation and storage: -40 °C to +100 °C protection class. Electronics: IP 67 Length: diameter 75mm. 14mm Two-core cable. 1.4m. Diameter 5mmsensor properties -40℃ 82.50kΩ 8.08V 0°C 32.91kΩ 6.37V 60°C 6.59kΩ 2.68V
DOL 139 CO2 Humidity and Temperature Sensor
From
€542.69*
Manufacturer item no.: 140283
DOL 139 is a sensor for measuring carbon dioxide/CO2, relative humidity and temperature. The sensor is used to monitor and control homes and industrial environments. The sensor is protected by a sturdy housing and behind a carefully selected filter. The sensor comes with cable and a cap to protect the sensor -ring washing and disinfection.
TECHNICAL SPECIFICATIONS
Output voltage range: 0 - 10 VDC
Limited output power per port: 20 mA
Output Impedance: <1Ω
Recommended load impedance: >100 kΩ max.
Cable length: at 1.50 mm2 200m
Load Impedance: >0.5kΩ
Relative humidity: measuring range 0-100%RH
Resolution: 0.1V/%RH
Accuracy: +10 °C - +40 °C (40-80%RH)+/-3 %RH
Accuracy: 10% RH - 95% RH +/-3 + 0.02 x measured value %RH
Time constant: T63: 4 min at 0.5 m/s air speed
Temperature measuring range: -40 – +60 °C
Resolution: 0.1V/AC
Accuracy: +10°C - +40°C +/-0.75°C
Accuracy 0°C - +60°C +/-1.5°C
Time constant T63 7 min at 0.5 m/s
Air velocity CO2 measurement range 0-10000ppm
Resolution: 0.001V/ppm
Accuracy: 400 - 10000 50ppm + 5% of reading
Time constant T63: 2 min at 0.5 m/s air speed
Supply voltage: 13.5 - 30 VDC
Supply current idle: 9 mA
maximum load: 105mA
Temperature operation CO2: 0 - +50 °C temperature,
Operation: -40 - +60 °C temperature,
Storage: -40 - +70 °C
IP classification: IP67 (DIN 40050-9)
NEMA-1, 3, 4, 6
DOL 16 light 0-100/1000LUX 0-10V M12 Plug
From
€168.82*
The DOL 16 is a sensor for measuring light intensity in lux. The sensor was developed for the harsh operating conditions in livestock housing, but is also suitable for numerous industrial purposes. Light intensity or illuminance plays an important role in optimizing broiler growth and laying hen egg production. Active control of the light intensity using the DOL 16 helps to increase production and save energy. The sensor has two 0-10 V analogue outputs with very low. output resistance and comprehensive protection against short circuits and cable faults. The sensor is controlled by a microprocessor and has a two-color light-emitting diode (LED) for communication of operating status and error diagnostics.
TECHNICAL SPECIFICATIONS
Measuring range:
Output 1: Lux 0-100*
Output 2: 0-1000
Accuracy:
Output 1: 5 - 100 lux +/- 4% at 0 - 40 oC (32 - 104 °F)*
Output 2: 25-1000 lux+/-8% at 0-40°C (32-104°F)
Output signal :
Output 1: 0.1V / 1lux
Output 2: 0.1V / 10lux
Time constant sec. Typ. 2 max. 15
Supply voltage (Usupply) V DC 11 - 30
Supply current mA 12 no load55 max load
Load Ω >500 – 10M
Recommended burden kΩ >100
Output current mA 20 per output (current limited)
Output impedance Ω<1
Temperature, operating °C (°F) -40 – 60 (-40 – 140)
IP rating IP (NEMA) 67 (6)
Cable connection (M12 version)
M12 male (female) with 2 m (6.6 feet) 4 x 0.33 mm2 (22AWG) cable
Cable max. cable length m 100 0.82 mm2
Illustration similar
DOL 16/104/114 protection cap
€24.60*
Manufacturer item no.: 140298Protective cap for cleaning, transport and storage1 set contains 5 pieces
DOL 16/104/114 Radiation shield
From
€77.50*
Manufacturer item no.: 140245Protective housing for operating humidity sensors under outdoor climate conditionsProtects the sensor from direct rain and sunlightSuitable for DOL 16/104/114
DOL 18 hose Ø16/2m
From
€5.80*
Version:
Ver. 1
|
Negative pressure:
Schlauch Ø16/2m
Manufacturer item no.: 140235Accessory set - DOL 18 version 1 and 2Ø 16 mmLength 2mIllustration similar
DOL 19 CO2 sensor 0-10,000 PPM
From
€338.12*
Manufacturer Art. No. 140231DOL 19 is a carbon dioxide/CO2 sensor intended for measurements in barn and industrial environments. The measuring range of the sensor has been carefully selected to ensure the comfort of the animals and also to monitor possible error conditions in direct combustion housing. The sensor is protected by a sturdy housing and is behind a carefully selected filter. The sensor is supplied with a plug and cableTECHNICAL DATAReadings: Measuring principle Non-Dispersive Infrared Technology (NDIR) Measuring range: 0...10,000 ppmAccuracy at 25 °C (77 °F) and 1013 mbar: 0-7000: 50ppm +5% of reading 7,000-10,000: 100ppm +5% of reading Temperature dependency: type. 1ppm CO2/°C (-20…45°C) Sample rate: Approx. 15 sec Analog output: 0...10,000 ppm voltage 0 - 10 V and current 4 - 20 mA Load: > 10 kΩ ≤ 500 Ω Recommended burden: ≥ 100 kΩ 500 ΩGenerally Supply voltage: SELV 15 – 35 V DC SELV = Safety Extra Low Voltage Power supply voltage output: Typ. 16mA current output: max. 36mA max. 0.5 A in 0.3 s max. 0.5 A in 0.3 s Warm-up time: < 5 min Housing / protection class polycarbonate / IP54 Electrical connection Cable with M12 connector cable 2m. 4 x 22AWG / 0.34mm2 Electromagnetic compatibility EN 61326-1 EN61326-2-3 working temp. and conditions -20...60 °C (-4...140 °F) 0...100 % RH (non-condensing) storage temperature. and conditions -20...60 °C (-4...140 °F) 0...95 % RH (non-condensing)
iDOL 20 SCR capacitive sensor 20-280V AC/DC
From
€88.50*
Version:
iDOL
|
Sensortype:
SCR
Manufacturer item no.: 103275The iDOL 20R sensor is a flat sensor typically used for level control in feed bins, bowls, silos and bins and for controlling feed lines in poultry production. It can be mounted on the outside of the plastic feed container because it can detect feed through plastic.Adjusted via the SmartAdjust appThe sensitivity of the iDOL 20 sensor can be adjusted to different feed types with the SmartAdjust app. To accommodate different engine controllers, the sensor on and off delay can be adjusted using the SmartAdjust app. It is also possible to adjust the output function (inverts the ON/OFF function of the sensor) via the app.TECHNICAL DATAelectricSupply voltage 20-280 VAC/VDCMinimum. ON current (Im) mA RMS/DC < 10 (Ue = 20 - 90) < 4 (Ue = 90 - 280)Off current (Ir) mA RMS/DC < 3 (Ue = 20 - 90) < 1 (Ue = 90 - 280)Voltage drop (Out) (current > 20mA) < 6mA RMS/V DCTime delay, switch on 150 msTime delay from 0-3600 sTime delay on 0-3600 sSwitching distance 0-12 mmHysteresis 8-10%On timer 0-7200 sEnvironmentAmbient temperature, operation and storage -20°C to +70°CProtection class IP 67
DOL 26 CA-P-M18-NF-CA-NPN-2-2T
From
€60.75*
Manufacturer Item No.: 105113
The DOL 26/105113 is a complete 18mm sensor series. Thanks to its mechanical design, the DOL 26 can be ideally integrated into applications with limited space. Versions with "full-return" of the cable are particularly suitable for feeding bowls. In standby mode, the DOL 26 consumes little power - therefore several sensors can be used simultaneously on the same contactor. This allows control of cross auger installations. The DOL 26 is particularly immune to EMI, short circuits and overloads, i. H.; there is no risk of burning the sensors due to assembly errors. TECHNICAL SPECIFICATIONS
Mains voltage (Ue): 10 - 36VDC
Frequency (fe): - Hz
Max Ripple: 10%
Max current (Ie): 500mA DC
Direct connection to Ue (current >> 500 mA) without damaging the sensor: > 10 times
Voltage drop, output ON (Ud): < 2.5 VDC
Temperature, operating: -20 - +70 (-4 - +158)°C (°F)
Temperature, storage: -40 - +80 (-40 - +176)°C (°F)
Degree of protection: IP69k (DIN 40050-9)
DOL 26 CA-P-M18-NF-CA-PNP-2-2T
From
€66.70*
Manufacturer item no.: 105108
The DOL 26 is a complete 18mm sensor series. Thanks to its mechanical design, the DOL 26 can be ideally integrated into applications with limited space. Versions with "full-return" of the cable are particularly suitable for feeding bowls. In standby mode, the DOL 26 consumes little power - therefore several sensors can be used simultaneously on the same contactor. This allows control of cross auger installations. The DOL 26 is particularly immune to EMI, short circuits and overloads, i. H.; there is no risk of burning the sensors due to assembly errors.
TECHNICAL SPECIFICATIONS
Sensor Type SCROutput Type BreakSurface Ø18 mm smoothMains voltage (Ue): 20-280VAC / VDC
Frequency (fe): 47 - 63 Hz
Max Current (Ie): 500mA RMS / mA DC
Load dip current: < 2.5A at 30 msA
Direct connection to Ue (current >> 500 mA) without damaging the sensor: > 10 times
Min. ON current (Im):< 10 (Ue = 20 - 90) ; < 6 (Ue = 90 - 280)mA RMS / mA DC
OFF current (Ir): < 3 (Ue = 20 - 90) mA RMS / mA DC; < 1 (Ue = 90 - 280) mA RMS / mA DC
Voltage drop, output ON (Ud): < 6 V RMS / V DC
Temperature, operating: -20 - +70 (-4 - +158)°C (°F)
Temperature, storage: -40 - +80 (-40 - +176)°C (°F)
Degree of protection: IP69k (DIN 40050-9)
iDOL 27 CA-P-M30-NF-CA-SCR
From
€70.00*
iDOL 27 is a capacitive sensor for detecting loose and solid materials. • SCR output versions are available in 2-wire versions. • The products are suitable together with contactors, relays, PLCs and similar in the agricultural and industrial sectors. • iDOL 27 is immune to EMI, short circuits and any overload. No more burned out sensors due to installation errors. • Very low power consumption when switched off – allows the possibility for sensors working in parallel on the same contactor. Unique control option Cross worm systems. • Protection class IP69k and NEMA 1/3/4/6/12/13 The ON and/or OFF delay and sensitivity of the sensor can be adjusted to different motor control units using the SmartAdjust app. The iDOL 27 is easy to adjust with the SmartAdjust app. The SmartAdjust App can be downloaded from the Google App Store. Simply search for SmartAdjust or scan the QR code on the product.
TECHNICAL SPECIFICATIONS
Model:105380
Mains voltage (Ue): 20-280VAC / VDC
Frequency (fe): 47-63Hz
Max Current (Ie): 500mA RMS / mA DC
Load Dip Current: < 2.5A @ 30ms A
Direct connection to Ue (current >> 500 mA) without damaging the sensor: > 10 times
Min. ON current (Im): < 10 (Ue = 20 - 90)mA RMS / mA DC; < 6 (Ue = 90 - 280) V
OFF current (Ir): < 3 (Ue = 20 - 90)mA RMS / mA DC; < 1 (Ue = 90 - 280)mA RMS / mA DC
Voltage drop, output ON (Ud): < 6 V RMS / V DC
Detection speed: > 15 Hz
Time delay OFF* (adjustable): 0.1 – 600 s
Activation distance (Sn) (adjustable): 0 - 20 (0 - 0.79) mm (inches)
Safe Activation Distance (Sa)*: 4 - 15 (0.16 - 0.59) mm (inches)
Repeatability (R): 5%
Hysteresis (H): 4 - 10%
Temperature, operating: -20 - +70 (-4 - +158) °C (°F)
Temperature, storage: -40 - +80 (-40 - +176) °C (°F)
Degree of protection: IP69k (DIN 40050-9)
NEMA 1, 3, 4, 6, 12, 13
iDOL 28RG 20-280V AC/DC
From
€96.56*
Surface:
Thread M30
|
Switching delay:
0-3600s Aus
The iDOL 28R is a capacitive relay sensor for the detection of feed, grain and solids in a feeding system. The sensor has a relay output with direct switching. The sensor has a white LED to illuminate the feeding bowl. A capacitive relay sensor is typically used as an empty, full and level indicator in tanks, silos and containers. The powerful integrated relay controls many functions directly. iDOL 28R series of capacitive relay sensors are robust and easy to operate. The SmartAdjust app makes it easier to change the settings of the product parameters depending on the model. The settings of the iDOL 28R can be adjusted using the SmartAdjust App, which can be downloaded from the Google Play Store.
TECHNICAL SPECIFICATIONS
Model: 100698
Mains Voltage: 20-280V AC/DC
Frequency: 47-63Hz
Max. voltage of the relay switch: 250 volts AC
Max. power of the relay switch: resistive load: 5 A ;
Inductive load: 2 A
Min. relay current 100 mA at 12 V DC
Safety: Relay switch and mains voltage are galvanically isolated. Test voltage 4kV AC
Activation distance: Adjustable between 0 and 20 mm depending on the material. Factory setting for grain
Time Delay: Adjustable between 0 and 600 seconds
Degree of protection: IP 69k. NEMA 1, 3, 4, 6, 12, 13
Ambient temperature, operation: -20 to +70 °C (-4 to +158 °F)
Ambient temperature, storage: -30 to +80 °C (-22 to +176 °F)
Length: 117mm (4.61”)
Diameter: 30mm (1.16”)
Cable: 5 × 0.5 mm2 (5 × AWG20) 2 m (6.6 ft)
DOL 41R capacitive sensor, 90-250 V AC
From
€77.10*
Manufacturer Art. No. 100671DOL 41R a capacitive sensor is typically used as an empty, full and level indicator in tanks, silos and containers. The powerful built in relay means it can control many functions directly. DOL 41R Model 100671 has no time delay. The relay switches as soon as the sensor activates and remains in that position until the activation influence ceases.TECHNICAL DATA Model:100671 Supply voltage: 90 - 250 V AC Frequency: 50 - 60 Hertz Consumption: 2VA Relay Switch Max Voltage: 250 VAC Relay switch max. power AC: 5 A at cos φ = 1, 2 A at cos φ = 0.8, 0.35 A at cos φ = 0.4 Relay switch max. power DC: 5 A at 0 - 30 V DC Safety: Relay switch and supply voltage are galvanically isolated. Test voltage 4 kV AC Activation distance: Adjustable 0 - 15 mm depending on the material. Factory setting for grain Time Delay: Adjustable 0-240 min. Factory setting for 30 sec. Protection class: IP67 Ambient temperature, operation: -20 °C to +70 °C / -4 °F to +158 °F Ambient temperature storage: -30 °C to +85 °C / -22 °F to +185 °F Smooth surface Ø30 mmAnother variant available:DOL 41R capacitive sensor, 10-30 V AC/DC
DOL 44R-33 capacitive sensor10-30V AC/DC
From
€79.50*
Manufacturer Item No.: 100309
The DOL 44R-33 is a complete 33mm series of capacitiveFeed sensors with relay output. The sensors have arobust functionality and are easy to use. The settingsCan be easily removed with a small screwdriver using two trimmerschange. DOL 44R has a high level of immunity to interferenceNoise from electrical communication technology (e.g. from mobile phones)and transients (e.g. from motors or switching devices). TheProtection class IP69K offers the greatest possible protection against water and othersliquids, e.g. B. when cleaning livestock stalls.DOL 44R is available in a variety of versions including the DOL44RH with integrated heater for refrigeration and applicationswith high humidity and the DOL 44RT is used to collect feed in pipes.
TECHNICAL SPECIFICATIONS
Model:100309
Supply voltage: 10-30V AC/DC
Frequency: 50 - 60 Hertz
Consumption: 2VA
Relay Switch Max Voltage: 250 VAC
Relay switch max. power AC: 5 A at cos φ = 1, 2 A at cos φ = 0.8, 0.35 A at cos φ = 0.4
Relay switch max. power DC: 5 A at 0 - 30 V DC
Safety: Relay switch and supply voltage are galvanically isolated. Test voltage 4 kV AC
Activation distance: Adjustable 0 - 15 mm depending on the material. Factory setting for grain
Time Delay: Adjustable 0-600 sec. Factory setting for 30 sec.
Protection class: IP69K
Ambient temperature, operation: -20 °C to +70 °C / -4 °F to +158 °F
Other variants available on requestIs compatible with the following products: VC11RN, VC11RT, VC12RN, VC12RT
DOL 45R T-sensor, 10-30 V AC/DC
From
€10.50*
Manufacturer item no.: 100682DOL 45R-T, a capacitive sensor, is typically used as an empty, full and level indicator in downpipes of feeding systems / automats. The powerful onboard relay means it can control many functions directly. Using new microcomputer technology, all functions have been optimized and combined in one sensor. DOL 45R. are variants with fewer functions. Sensitivity and delay length are set with two switches. LEDs indicate when the switches are activated. Of course all settings can easily be changed again later.TECHNICAL DATA Model:100682 Supply voltage: 10-30V AC/DC Frequency: 50 - 60 Hertz Consumption: 2VA Relay Switch Max Voltage: 250 VAC Relay switch max. power AC: 5 A at cos φ = 1, 2 A at cos φ = 0.8, 0.35 A at cos φ = 0.4 Relay switch max. power DC: 5 A at 0 - 30 V DC Safety: Relay switch and supply voltage are galvanically isolated. Test voltage 4 kV AC Activation distance: Adjustable 0 - 15 mm depending on the material. Factory setting for grain Time Delay: Adjustable 0-600 sec. Protection class: IP69K Ambient temperature, operation: -20 °C to +70 °C / -4 °F to +158 °F Ambient temperature storage: -30 °C to +85 °C / -22 °F to +185 °F
Sensor holder not included